BLUETTI Elite 100 V2: Runtime & Specs

By Hicham M. · Specs from BLUETTI's published documents, as of September 2026 · How we calculate

The BLUETTI Elite 100 V2 is a 1,024 Wh LiFePO4 power station with 1,800 W of continuous AC output. It runs a typical full-size fridge for about 15 hours.

Capacity1,024 WhLiFePO4

Output1,800 Wsurge not published

Solar input1,000 W12–60 V

Weight25.3 lbnot expandable

Check price on Amazon View at BLUETTI Calculate runtime for your devices

We may earn a commission if you buy through these links. It never changes our numbers, and every model in our database is included whether or not it pays us. Learn more.

Simulated runtimes (not measured)

Nobody tested this unit for this page. These figures come from a computer simulation of the Elite 100 V2, and they are estimates. The plain runtime table below divides energy by average draw at 85% efficiency. The simulation also charges the battery for the power the inverter burns just by being switched on, which is why small loads come out shorter. Where we have measured a unit, the measurement is shown separately and labeled as measured.

Simulated runtimes for the BLUETTI Elite 100 V2
Device	Spec-sheet math	Simulated, typical	Likely range	Simulated at 0 °C
Wi-Fi router + modem	2.4 days	38 hours	37 hours to 39 hours	32 hours
CPAP (no humidifier)	29 hours	23 hours	23 hours to 24 hours	20 hours
Starlink Standard	9.7 hours	9.2 hours	9 hours to 9.5 hours	7.8 hours
Refrigerator (full-size, ENERGY STAR)	15 hours	14 hours	13 hours to 14 hours	12 hours

Nonstop runtime from full to battery cutoff. Likely range = middle 80% of 200 simulated runs with the uncertain inputs varied. The inverter idle draw is BLUETTI’s own figure for this model, about 10 W, from its user manual. See why idle draw matters.

How this was simulated

The battery is stepped down every 2 minutes until it reaches cutoff, for 200 runs per device. Results are seeded, so the page shows the same numbers on every build.
Battery draw = load + inverter idle draw + 4–8% of the load + a loss that rises with load squared (4% at full output).
Usable capacity = 92–98% of rated Wh, for protection cutoff and aging.
At 0 °C, 80–90% of that capacity is assumed available.
Fridges cycle on and off every 30–50 minutes at the share of the time set by their average draw. The inverter idle draw continues while the compressor is off.
Devices that exceed this model's output or surge rating are left out. Loads are US 120 V devices.

These ranges are assumptions about a typical unit. They are not manufacturer figures for the BLUETTI Elite 100 V2. How we calculate · How we use AI

How long will the Elite 100 V2 run your appliances?

Nonstop runtime for one device at a time, using typical US wattages and 85% inverter efficiency. Devices marked ✕ can't run on this model.

Estimated runtime by appliance for the BLUETTI Elite 100 V2
Device	Avg draw	Runtime
LED light bulb	9 W	4 days
Phone charging	10 W	3.8 days
Wi-Fi router + modem	15 W	2.4 days
Laptop	50 W	17 hours
CPAP (no humidifier)	30 W	29 hours
CPAP with heated humidifier	60 W	15 hours
Starlink Standard	90 W	9.7 hours
TV	100 W	8.7 hours
Mini fridge	29 W	30 hours
Refrigerator	58 W	15 hours
Chest freezer	29 W	30 hours
Sump pump (1/3 HP)	160 W	5.4 hours
Sump pump (1/2 HP)	210 W	4.1 hours Surge?
Window AC	225 W	3.9 hours
Drip coffee maker	1,000 W	52 min
Microwave	1,500 W	35 min
Space heater	750 W	1.2 hours
Well pump	33 W	Needs 240 V

Surge? = this model has no published surge rating, so starting motors and compressors may or may not work. Fridges, freezers, pumps and AC units cycle on and off, so we use their average draw. Want a mix of devices on a schedule? Use the runtime calculator.

The Elite 100 V2 in action

BLUETTI's own video, so expect a sales pitch. It loads from YouTube only when you press play.

**BLUETTI Elite 100 V2**Official video from BLUETTI Support, plays from YouTube

What the Elite 100 V2 can't power

Well pump (1/2 HP submersible): needs 240 V

Solar charging time

Hours of good sun to charge from empty, assuming panels deliver 75% of their rating.

Panels	Power in	Hours of sun
100 W of panels	75 W	14 hours
200 W of panels	150 W	6.8 hours
400 W of panels	300 W	3.4 hours
1,000 W of panels	750 W	1.4 hours

Check panel voltage and wiring with the solar charging calculator.

Full specifications

Battery capacity	1,024 Wh
Amp-hours at 12 V (converted) How we convert	85.3 Ah (80 Ah at 12.8 V)
Battery chemistry LFP vs NMC	LiFePO4 (LFP)
Continuous AC output	1,800 W
Surge (peak) output	Not published
Power Lifting (heating devices)	2,700 W
AC voltage	120V
AC outlets	—
USB-C ports	2 (up to 140 W)
USB-A ports	2
12 V car outlet	Yes
Max solar input	1,000 W
Solar voltage range	12–60 V
Solar max current	20 A
Max AC charging power	1,200 W
AC charging time (maker claim)	0–80% in 45 min (1,200W Turbo)
Expandable	No
UPS / EPS switchover What this means	10 ms
Cycle life What this means	4,000 cycles (to 80%)
Weight	25.3 lb
Warranty	5 years

Notes: AC outlet count not stated in page/manual text (page says '11 ports' total). Surge not published. AC input 1,800W incl. bypass; 1,200W charging. Page lists 25 lb, manual 25.3 lb.

Specs from BLUETTI's published documents, as of September 2026. Found an error? Tell us.

Sources

Similar power stations

Questions

How long will the BLUETTI Elite 100 V2 run a refrigerator?

About 15 hours for a typical ENERGY STAR full-size fridge averaging 58 W, assuming 85% inverter efficiency. Older or larger fridges use more. Try your own numbers.

Can the BLUETTI Elite 100 V2 run a microwave?

Yes. A typical 1,000 W microwave pulls about 1,500 W from the outlet, within its 1,800 W continuous output. A full battery gives about 35 min of cooking.

How many amp-hours is the BLUETTI Elite 100 V2?

The BLUETTI Elite 100 V2 works out to about 85.3 Ah at 12 V, or 80 Ah at 12.8 V, the nominal voltage of a 12 V LiFePO4 battery. Both are our conversion of BLUETTI's 1,024 Wh rating: amp-hours = watt-hours ÷ volts. The battery inside may run at a different voltage, so an amp-hour figure in a manual or on a product listing can look very different for the same energy. For scale, a 12 V 100 Ah LiFePO4 battery holds 1,280 Wh, so this model holds about 80% as much as one. How we convert amp-hours.

How long does the BLUETTI Elite 100 V2 take to charge?

BLUETTI's published charging claim: “0–80% in 45 min (1,200W Turbo)”. Max AC charging power is 1,200 W. With solar, it accepts up to 1,000 W. With 1,000 W of panels that's roughly 1.4 hours of good sun from empty.

Is the BLUETTI Elite 100 V2 expandable?

No. Its capacity is fixed at 1,024 Wh.

Does the BLUETTI Elite 100 V2 work as a UPS?

BLUETTI lists a 10 ms switchover time, so it can keep devices like routers and computers running when the power drops. Check that your specific device tolerates the switch before relying on it for anything critical.